Program the Real Arm · xArm 850

Program the Real Arm

This part is for the person who programs the arm. You turn one manufacturing task into a deterministic program, test it step by step, and leave it ready for an agent to call. The program is written in Python on UFACTORY's software development kit, and nothing here runs on the real arm without the instructor's approval.

Warning

Run a new or changed program on the arm only with the instructor's approval, the operating checklist done, and the emergency stop within your reach12.

What the Course Asks

  • A deterministic program that makes the machine perform a defined task safely and repeatably. It may take defined inputs and report its status; connecting it to an agent and to MIX comes in the next step3.
  • The task is approved by the instructor and described by its objective, inputs and materials, expected output, initial state, sequence, completion criteria, safety conditions and likely errors4.

This Program's Task

For each card of a job, the arm moves home, picks the card with the vacuum gripper, places it on the staging stack for the card's variant, releases it and returns home. When the job is done it waits at home for the next one5.

  • Inputs: a job that names the card's variant and how many, and one card at a time pushed into an L-shaped corner stop of tape on the pick surface56.
  • Materials: cards in black and other primary colors, all with a metallic gleam. Each color is a variant, and the variant chooses the stack7.
  • Output: the job's cards on their stack, the arm at home, a JOB_COMPLETE event and the state READY89.
  • Initial state: no controller error, the arm in position mode with Manual Mode off, the controller's tool point and payload as the station file gives them, and a card in the corner stop105.
  • Completion: a cycle is complete when the card's release is confirmed and the arm is home; a job, when the completed cycles equal its quantity8.

Without the Camera

Nothing checks the card: the job's variant is trusted and chooses the stack, and every cycle reports that no inspection ran. The camera's check of the card's color and defects is built as an extension of the same program and tested on still images11.

The Safety Requirements
  • Get the instructor's approval before running a new or changed program1.
  • Review it for unsafe motion, excessive speed, improper power, invalid parameters and collisions1.
  • Use simulation, dry runs and reduced speed whenever you can1.
  • Confirm the guards, interlocks, emergency stops and safety zones are active. Never bypass a safety function or exceed an approved limit1.
  • Keep the emergency stop within reach while you test, and stop at once if the arm does anything unexpected1.
  • Back up the approved program before you change it1.

The Pages

Printed from https://www.anotherplace.com/learn/en/xarm-850/program. Every line cites its source on that page.

Provenance

References · 17

Each number in the text points here. Every entry states its confidence class in words and keeps its evidence one click away. How to read the labels.

Key to the badges
Confidence: Verified
A manufacturer or IntelliMake document says so, the project owner stated it as the design, or it was observed directly. It does not mean anyone measured it at S2.
Confidence: Inferred
Reasoned from Verified facts. The reasoning is printed with the record.
Confidence: Assumed
Plausible but untested. The record says how it would be checked.
Kind: Gap
Not known. No figure or answer is given in its place.
Kind: Contradiction
Sources disagree. Both sides are shown, and the site does not pick one silently.
Kind: Recommendation
Project advice drawn from the records it cites. Not a fact about the machine and not a confidence class, so the filter never hides it.
Awaiting cell access
Awaiting cell access: could be confirmed or corrected once the physical S2 cell can be observed.
This project's design (its simulation, agent and arm program), not the physical cell
This project's design (its simulation, agent and arm program), not the physical cell.
  1. Confidence: Verifiedint-643

    The record says

    The course's safety requirements for programming: get approval before running a new or modified program; review it for unsafe motion, excessive speed, improper power, invalid parameters and potential collisions; use simulation, dry runs, reduced speed or reduced power whenever possible; confirm that the required guards, interlocks, emergency stops and safety zones are active; never bypass safety functions or exceed approved machine limits; keep access to the emergency stop during initial testing; stop testing at once if the machine behaves unexpectedly; and back up the approved working program before changing it.

    Evidence · 8 citations

    Obtain approval before executing a new or modified program.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Review the program for unsafe motion, excessive speed, improper power, invalid parameters, and potential collisions.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Use simulation, dry runs, reduced speed, or reduced power whenever possible.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Confirm that required guards, interlocks, emergency stops, and safety zones are active.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Never bypass safety functions or exceed approved machine limits.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Maintain access to the emergency stop during initial testing.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Stop testing immediately if the machine behaves unexpectedly.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Back up the approved working program before making further changes.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  2. Confidence: Verifiedcomp-024

    The record says

    The 850's emergency stop button is on the control box. Pressing it makes the control box decelerate the arm in software, stop all motion and clear cached commands, then remove power from the arm within 300 ms.

    Evidence · 1 citation

    Quote not shown (over 40 words). See the source at: 2.1.2 Emergency Stop Button (docs site 'UFACTORY 850 硬件手册', English version; names the machine 'UFACTORY 850').

    UFACTORY 850 Hardware Manual (online), 2. Hardware Installation · UFACTORY · 2.1.2 Emergency Stop Button (docs site 'UFACTORY 850 硬件手册', English version; names the machine 'UFACTORY 850')

    © UFACTORY · All rights reserved; quoted briefly as evidence · retrieved 2026-09-21

  3. Confidence: Verifiedint-636

    The record says

    IntelliMake's course step 'Program Your Machine' asks each learner to program their assigned Phase 1 Factory machine to perform a defined manufacturing task safely and repeatably, with a deterministic machine-level program that may accept defined inputs and report status. Connecting the machine to an AI agent and to MIX belongs to the next step, 'Agentify Your Machine'.

    Evidence · 3 citations

    The purpose of this assignment is to develop the ability to program your assigned Phase 1 Factory machine to perform a defined manufacturing task safely and repeatably.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Purpose', first paragraph

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    The program may accept defined inputs and report status, but it does not need to interpret higher-level production goals, coordinate through MIX, or make autonomous decisions.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Scope Boundary'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Connecting the machine to an AI Agent and MIX will be addressed in Step 4

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Purpose', second paragraph

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  4. Confidence: Verifiedint-637

    The record says

    The course asks for an instructor-approved task, described by its objective, its required inputs and materials, its expected output, the machine's initial state, the sequence of operations, the completion criteria, the safety conditions and constraints, and the likely errors or abnormal conditions.

    Evidence · 9 citations

    Select an instructor-approved task appropriate for your assigned machine.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    The objective of the task

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Required inputs and materials

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Expected output

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Initial machine state

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Sequence of operations

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Completion criteria

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Safety conditions and constraints

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Likely errors or abnormal conditions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '1. Define the Manufacturing Task', the list under 'Describe'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  5. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-644

    The record says

    This project's program for the xArm 850 runs one task without the arm's camera. For each card of a job it moves home, picks the card at a taught pick pose with the vacuum gripper, places it on the staging stack for the job's variant, releases it and returns home; when the job is done the arm waits at home for the next job. Each card is pushed into an L-shaped corner stop of tape on the pick surface, so it lies under the taught pick pose.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: step3/program.py and step3/run.py run this cycle with --no-camera, and the station file step3/stations/s2-850.json describes the corner stop (pick.fixture), at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites S277, the statement the task was taken from, and his agreement to it.

    Evidence · 2 citations

    vacumm triggered, gripper moved, piece released, arm goes back to starting position waiting for next order

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

    ok, I agree. Please move forward

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19), his answer to the recommendation

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

  6. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-654

    The record says

    In its wait-for-job mode (--serve) this project's program moves home, reports READY and reads one command per line from standard input, as a JSON line or a short form a person types: START_JOB with a variant and a quantity from 1 to the room left on that variant's stack (typed as start black 3), PAUSE (p), RESUME (r), STOP (s), STATUS (status) and SHUTDOWN (quit). A command that cannot run in the current state is refused with a COMMAND_REFUSED event, never queued. Every event is one JSON line on standard output and in the run's log file. It exits with 0 at READY or a completed job, 2 at FAULT, 3 at STOPPED and 4 when it refuses to start.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: step3/run.py (--serve, the exit codes) and step3/events.py (the JSON lines on standard output and in runs/<stamp>/events.jsonl), at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites S277, where waiting for the next order was asked for, and the course's suggested interface.

    Evidence · 4 citations

    vacumm triggered, gripper moved, piece released, arm goes back to starting position waiting for next order

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

    ok, I agree. Please move forward

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19), his answer to the recommendation

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

    Start task | Command | Initiates the approved program | START_JOB

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Suggested Program Interface Table', 'Start task' row

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Task completion | Event | Confirms successful completion | JOB_COMPLETE

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Suggested Program Interface Table', 'Task completion' row

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  7. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-646

    The record says

    The cards the xArm 850 handles are black and other primary colors, all with a metallic gleam. This project's program has one variant per card color, and the job's variant chooses the staging stack the card goes to.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: the station file step3/stations/s2-850.json lists the variants under 'variants', each naming its stack; their ids and stacks are labeled placeholders until the cards are named, at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites S276, the statement the colors were taken from.

    Evidence · 1 citation

    Card colors will be black and 0ther primary colors. They all seem to have a metallic gleam to it.

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S276 (2026-11-17, from the lab)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

  8. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-648

    The record says

    In one cycle this project's program moves home; checks that the job's stack has room; moves above the pick pose and descends straight down; switches the vacuum on and confirms the card is held; lifts; moves above the variant's stack, confirming the card is still held; lowers it straight down onto the stack; switches the vacuum off and confirms the release; retreats straight up and returns home. It then reports CYCLE_COMPLETE with the cycle time, and after the job's quantity JOB_COMPLETE, and returns to READY. Joint moves go between waypoints; straight-line moves are only the short descents, lifts and retreats.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: step3/program.py runs these steps in this order (the STEP events name them: home, pick_hover, descend, vacuum_on, verify_holding, lift, stack_hover, stack_place, vacuum_off, verify_released, stack_retreat, return_home), at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites S277, the sequence the program was built to.

    Evidence · 2 citations

    vacumm triggered, gripper moved, piece released, arm goes back to starting position waiting for next order

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

    Machine actions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  9. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-647

    The record says

    This project's program reports one of five states: READY (at home, no job running), RUNNING, PAUSED, FAULT and STOPPED. After FAULT or STOPPED it accepts only STATUS and SHUTDOWN: it never recovers by itself, and a person deals with the cause and starts the program again.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: step3/program.py defines the five states and refuses every command but STATUS and SHUTDOWN after FAULT or STOPPED, at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites the course's suggested states, which the program's extend.

    Evidence · 2 citations

    Machine state | Status | Reports current operating condition | Ready, Running, Paused, Fault

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Suggested Program Interface Table', 'Machine state' row

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Safe recovery behavior

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  10. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-650

    The record says

    Before a job this project's program reads the arm's readiness, and refuses with FAULT NOT_READY, sending nothing, if the controller reports an error, the arm is not in position mode (Studio's Manual Mode is refused), or the controller's tool point and payload differ from the station file's 126 mm and 0.61 kg.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: step3/arm.py reads the error, the mode, the tool point and the payload, and step3/stations/s2-850.json holds 126 mm and 0.61 kg read from the controller on 2026-10-22 (ops-210), at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites the controller's reading those figures were taken from.

    Evidence · 3 citations

    Start conditions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Weight 0.61 kg; centre of gravity CX 0, CY 0, CZ 53 mm

    UFACTORY Studio screens and a control-box photo for the xArm 850, 2026-10-22: what they show (OBSERVATIONS.md) · Derek Stringfellow · TCP after the update, table, 'Payload' row

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-22

    X 0, Y 0, Z 126 mm

    UFACTORY Studio screens and a control-box photo for the xArm 850, 2026-10-22: what they show (OBSERVATIONS.md) · Derek Stringfellow · TCP after the update, table, 'Offset' row, first part

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-22

  11. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-645

    The record says

    Without the camera, this project's program does not check the card: the job names its variant, which chooses the stack, and every completed cycle reports that no inspection ran. The camera's check of the card's variant and defects before the pick is built as an extension of the same program, tested on still images the arm's camera took with the arm standing still.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: each CYCLE_COMPLETE and JOB_COMPLETE event carries "inspection": "none (no camera)" and "variant_source": "job" (step3/program.py), and the extension is step3/camera.py, step3/vision.py and step3/tools/check_capture.py, at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites S277, where the camera was taken out of the loop and the extension agreed.

    Evidence · 3 citations

    I do not think we can test with the camera for the assignment at this point.

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

    the camera as a documented extension tested offline on real arm-camera captures, a `--no-camera` mode and a mode that waits for the next job

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19), the recommendation he agreed to (the session's words, not his)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

    ok, I agree. Please move forward

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S277 (2026-11-19), his answer to the recommendation

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

  12. Confidence: Verifiedint-638

    The record says

    The course asks for a flowchart, state diagram or sequence table made before programming, identifying the start conditions, operating states, inputs and sensor signals, machine actions, timing and parameter requirements, decision points, completion conditions, fault and stop conditions, and safe recovery behavior.

    Evidence · 10 citations

    Create a flowchart, state diagram, or sequence table before programming.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Start conditions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Operating states

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Inputs and sensor signals

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Machine actions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Timing and parameter requirements

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Decision points

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Completion conditions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Fault and stop conditions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Safe recovery behavior

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '2. Develop the Program Logic', the list under 'The logic should identify'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  13. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-656

    The record says

    This project's program is split so the same logic drives a simulated arm and the real one: arm.py (the only module that imports UFACTORY's Python SDK), fake_arm.py (the same interface without the SDK), program.py (the state machine), events.py (the events and the run log), run.py (the command line) and a station file per arm; its unit tests run on the simulated arm. It needs Python 3.11 or later. With --live it drives the real arm, whose address is given as an argument or the XARM_IP environment variable, never in a file; --dry-run connects and reads but moves nothing; --step makes one move per press of Enter. Two tools move nothing: vacuum_test switches the vacuum on and off, and record_waypoint reads the arm's pose for a waypoint.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: the files named are in step3/, with step3/tools/vacuum_test.py, step3/tools/record_waypoint.py, step3/tests/ and step3/README.md (install and run instructions), at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites the course's testing steps and S172, the decision to program in Python.

    Evidence · 3 citations

    Simulate or dry-run the program when possible.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Test individual steps at reduced speed or power.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Blockly will not be used due to the freedom of programming we will need, so our coding will be in Python.

    Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow · Statement S172 (2026-10-09)

    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04

  14. Confidence: VerifiedThis project's design (its simulation, agent and arm program), not the physical cellint-649

    The record says

    This project's program takes every waypoint, speed, wait and bound from a station file, never from its code, and labels each value with its status (placeholder, taught, measured or read from the controller) and its source. Before every move it checks the target against the station file's bounds (the pick area, a floor height, the workspace and the joint ranges) and sends nothing if the target is outside them. With the real arm it refuses to connect while a waypoint, the pick area, a stack, the floor, the workspace or a joint range is still a placeholder.

    Reasoning: The sentence on the program states the state of the program's own repository (~/projects/ie6000-lab, step3/), not something the cited source says: step3/stations/s2-850.json and its schema hold every value with a status and a source, step3/program.py checks each target before sending it (OUT_OF_BOUNDS), and step3/run.py lists the placeholders and does not connect, at commit 130b203 (2026-11-19), and docs/course-step3/ in this repository describes the same version. The corpus cites only sources kept under corpus/sources/ or at a public address (corpus/README.md, Source entries), so it cannot cite that repository; it cites the course's requirement to stay within the approved limits.

    Evidence · 2 citations

    The program must be developed and tested within the machine’s approved operating limits.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '3. Create or Modify the Machine Program', last line

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Review the program for unsafe motion, excessive speed, improper power, invalid parameters, and potential collisions.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · 'Safety Requirements'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  15. Confidence: Verifiedint-639

    The record says

    The course's testing process has seven steps: review the logic before enabling motion; simulate or dry-run the program; test individual steps at reduced speed or power; verify inputs, outputs, positions and parameters; test the complete sequence; record errors and program revisions; and repeat the operation to evaluate consistency. Faults that could damage equipment, materials or people are not introduced.

    Evidence · 8 citations

    Review the logic before enabling machine motion or processing.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Simulate or dry-run the program when possible.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Test individual steps at reduced speed or power.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Verify inputs, outputs, positions, and parameters.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Test the complete sequence.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Record errors and program revisions.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Repeat the operation to evaluate consistency.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', the numbered process

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Do not introduce faults that could damage equipment, materials, or personnel.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '4. Test and Debug the Program', last line

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  16. Confidence: Verifiedint-640

    The record says

    The course asks for the programmed task to be run for multiple cycles, when appropriate, and evaluated for task completion, repeatability, cycle time, output quality, positioning or process accuracy, the operator intervention required, the response to safe stops or expected errors, and readiness for integration into the Phase 1 Factory.

    Evidence · 9 citations

    Run the programmed task for multiple cycles, when appropriate, and evaluate:

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Task completion

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Repeatability

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Cycle time

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Output quality

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Positioning or process accuracy

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Operator intervention required

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Response to safe stops or expected errors

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Readiness for integration into the Phase 1 Factory

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '5. Verify Program Performance', the list

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

  17. Confidence: Verifiedint-641

    The record says

    The course asks how a future Machine Agent could interact with the program: the commands it could issue, the required task parameters, the machine status it could report, the completion and failure messages, the available communication methods (such as digital I/O, PLC tags, MQTT, an API, an SDK, file transfer or operator-interface actions), and the current limitations or integration gaps. Building the agent is not part of this step.

    Evidence · 7 citations

    Commands the Machine Agent could issue

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', the list under 'Document'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Required task parameters

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', the list under 'Document'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Machine status information that could be reported

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', the list under 'Document'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Completion and failure messages

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', the list under 'Document'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Available communication methods, such as digital I/O, PLC tags, MQTT, API, SDK, file transfer, or operator-interface actions

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', the list under 'Document'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    Current limitations or integration gaps

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', the list under 'Document'

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

    You are not required to build the Machine Agent in this assignment.

    'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course · '6. Identify the Agentification Interface', last line

    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12

Sources for This Page

  • 'Program Your Machine': the course's Step 3 assignment for the Phase 1 Factory machines (course text as attached by Derek, 2026-11-12) · IntelliMake Phase 1 Factory course (IntelliMake)
    IntelliMake course text, as attached by Derek Stringfellow · Project-internal record · retrieved 2026-11-12 · cited by 13 records here · Project copy; not published on this site.
  • Owner statements from 2026-09-24 onward (verbatim; S40 and later) · Derek Stringfellow (project owner)
    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-04 · cited by 6 records here · Project copy; not published on this site.
  • UFACTORY 850 Hardware Manual (online), 2. Hardware Installation · UFACTORY (manufacturer)
    © UFACTORY · All rights reserved; quoted briefly as evidence · retrieved 2026-09-21 · cited by 1 record here · Open the source
  • UFACTORY Studio screens and a control-box photo for the xArm 850, 2026-10-22: what they show (OBSERVATIONS.md) · Derek Stringfellow (project owner)
    Derek Stringfellow, project record · Project-internal record · retrieved 2026-10-22 · cited by 1 record here · Project copy; not published on this site.

IntelliMake diagrams are redrawn as native figures, © IntelliMake.org. UFACTORY does not endorse this platform.

All sources and attribution