Practice in the Simulator · xArm 6
Jog It, Automate It, Check It
Move a simulated xArm 6 at its station in the IntelliMake cell, automate a pick and place, and check every step against the arm's limits.
This station follows the cell's Phase 1 layout drawing, which is not to scale. The cabinets' sizes (or, for S7, their stated match) and the conveyors' lengths and heights are measured. The cabinets and the S1 conveyor are placed as in the drawing; the S4 conveyor's width and position, the gaps between the cabinets and the arm's place on its plate are placeholders. The tool and a held part stop at the cabinets, conveyors, plates and the engraver as at any solid object. How this station fits the cell.
Turn a joint and watch the tool tip for additional info.
Move the Arm
Each joint has three ranges and a margin; open Ranges under a joint to see them. Margin: a buffer kept inside the configured range. Operating: what is left. A jog past the operating range still runs here, marked ⚠ ran past a limit, so you can see it; at the end of the configured range, here UFACTORY's published range, it stops (⊘).
Ranges J1
- Published
- ±360° Verified spec-509
- Configured
- ±360° Verified UFACTORY's published range, the default
- Operating
- ±355° (configured − 5° margin)
Ranges J2
- Published
- −117° to 116° Verified spec-510Sources disagree (spec-516) other UFACTORY sources give −118° to 120°
- Configured
- −117° to 116° Verified Sources disagree UFACTORY's published range, the default; the figure its manual and product page give
- Operating
- −112° to 111° (configured − 5° margin)
Ranges J3
- Published
- −219° to 10° Verified spec-511Sources disagree (spec-517) other UFACTORY sources give −225° to 11°; another gives −255° to 11°
- Configured
- −219° to 10° Verified Sources disagree UFACTORY's published range, the default; the figure its manual and product page give
- Operating
- −214° to 5° (configured − 5° margin)
Ranges J4
- Published
- ±360° Verified spec-512
- Configured
- ±360° Verified UFACTORY's published range, the default
- Operating
- ±355° (configured − 5° margin)
Ranges J5
- Published
- −97° to 180° Verified spec-513
- Configured
- −97° to 180° Verified UFACTORY's published range, the default
- Operating
- −92° to 175° (configured − 5° margin)
Ranges J6
- Published
- ±360° Verified spec-514
- Configured
- ±360° Verified UFACTORY's published range, the default
- Operating
- ±355° (configured − 5° margin)
Focus a joint: ← → 1°, Shift+← → 0.1°, PgUp PgDn 10°, Home back to zero, Esc stops the simulation.
1 mm a press; Shift for 10 mm. The tool keeps its angle. X: along the row. Y: toward the back. Z: up.
Automate a Task
Record poses and grips as steps, then check the whole task. Record keeps each joint to 0.1°. Each move is checked along its path, as a joint move (every joint turns steadily from one pose to the next), not only where it ends.
No steps yet. Start from the example, or jog the arm and record your own poses.
Simulated check · not the arm's safety supervisor
Every limit has a kind. A safety alert is about a limit a real arm or cell must never cross: the workspace, a keep-out zone, the payload, a solid fixture, or a joint past what UFACTORY publishes. A teaching alert is about a move inside what the arm can do but past an operating limit set for this station, or a step that cannot be done from where the arm is (no posture reaches it, or there is nothing to grip or release). Here a move past a limit runs and is marked ⚠ ran past a limit. It is refused (⊘) when a joint goes past UFACTORY's range, when the tool or the held part meets a cabinet, a conveyor, a plate or the engraver, or when a step cannot be done at all.
A downloaded task is marked Unreviewed. It is a simulation file, not a program for an arm's controller.
The Scene
The ideal part never slips, so grip force and friction are not checked here. The payload check counts the tool's mass as well as the part's. Joint limits, the workspace, the keep-out zones and the station's cabinets, conveyors, plates and the engraver are checked at every sampled pose of each move. The workspace box, the keep-out zones and their clearance, and the joint margin are set for this station; the payload limit is UFACTORY's published payload for the arm. Joint limits here are UFACTORY's published ranges less the margin.
The scene in words
- S6 cabinet: 648 × 648 × 819 mm (size measured, placed as in the drawing) Assumed
- S6 mount plate: 300 × 300 × 25 mm (height measured; footprint a placeholder) Placeholder
- S7 cabinet (the 3D printer's station; the printer is not drawn): 648 × 648 × 819 mm (size and height stated to match the other cabinets; the height is adjustable; placed as in the drawing) Assumed
- S4 cabinet: 1275 × 590 × 826 mm (size measured; centered as planned) Assumed
- S4 engraver conveyor: 970 × 240 × 89 mm (belt measured; position as planned) Placeholder
- S8 cabinet (shipping): 648 × 648 × 819 mm (size measured, placed as in the drawing) Assumed
- S5 laser engraver (xTool F1 Ultra): 230 × 285 × 490 mm (carriage area, width and height measured) Placeholder
- Pick zone (S4 conveyor): 200 × 150 mm, center (-597.5, 0) Placeholder
- Place zone (S8, shipping): 200 × 150 mm, center (533.85, 0) Placeholder
- S5 laser engraver (xTool F1 Ultra) (Keep-out K1): 230 × 285 × 490 mm, from (-1012.5, -142.5, 914.4) to (-782.5, 142.5, 1404.4) Assumed
- Held part: hangs below the tool tip, which grips its top face (the default).
- Payload limit 5 kg Verified spec-502; the tool's mass counts against it Inferred lim-541
- Keep-out clearance 20 mm Placeholder; joint margin 5° Assumed
- Workspace, where the tool must stay: from (-1535, -323.85, 819.15) to (981.55, 981.55, 2000) mm Placeholder
Tool X, Y and Z: the tool tip's position in mm from the floor below the arm base. X to the right along the row from the S1 side, Y toward the back (S3 and S7), Z up. The simulator's own frame, not the real arm's. Assumed
In the twin framework this course uses, this station is a simplified, cell-level Digital Model: it simulates the arm, and no data flows to or from a real arm. Confidence: Inferred lvl-025: why the course places the simulator here
Scene file: IntelliMake cell: S6, version 0.3.0, draft.